Datamax-oneil ANDES 3 User Guide Manual de usuario

ANDES 3 User Guide 7A300028 Rev. A

6 1.4 Attaching Belt Loop System The belt loop system consists of two parts as seen in Figure 5:  A knob located on the back part of the printer

7 2 Loading Supplies 2.1 Adding Paper or Labels The printer can print text, bar codes and graphics on thermal receipt paper. See “Supply Specificat

8  Close the paper door and press close as shown in Figure 8. FIGURE 8 – CLOSING PRINTER 2.2 Tearing Paper The printer’s paper door acts as a

9 3 Using the Printer 3.1 Initial Power-Up and Self-Test Once the Battery is charged and the paper is loaded, an initial power up and self-test c

10 3.2 Connecting the Printer  The ANDES 3 printer supports Serial RS232 and IrDA compatible infrared communication interfaces. Radio frequency (

11 3.2.2 Setting Dip Switches ON12345678 FIGURE 12: EXAMPLE: DIP SWITCH #1 SHOWN IN ‘ON’ POSITION Note: Use care when changing dip switch set

12 3.3 Communications  The ANDES 3 Printer is able to support two modes of communication simultaneously – Either RS232 and IrDA (If Dip switch #1 i

13 3.4 Infrared Communications Mode (IrDA)  Dip Switch #1 must be in the <ON> position.  The printer can be powered up by pressing the pow

14 Table 4 - Magnetic Card LED Indicator LED Indicator State Status Green ON OFF Ready/waiting for card to be swiped. Good swipe - Card data re

15 3.7.1 ASCII Control Characters Character Hex/Dec CONTROL ACTION EOT 04/04 End Of Text BS 08/08 Back Space HT 09/09 Horizontal Tab

16 Table 5 shows the International and PC Line Character sets from 32 through 255. Table 5: International and PC Line Draw Character Set

17 3.7.6 Smart Card Reader Control Commands (when SCR is installed) Command String Printer Action ESC - ‘M’ - ‘nn’ - ‘7’- Cr Select SCR in di

18

19 4 Printer Maintenance 4.1 Print Head Cleaning Instructions You may need to clean the print head and platen roller after printing a number of roll

20 4.2.1 Important Notes on Charging Batteries  The model ANDES 3 printers require an adapter output of 10VDC/1.32A.  The battery Fast-charge i

21  Press <ON/OFF> switch and wait until all LED’s are off  Plug the AC power adapter into the printer. Press <ON>; the green LED is

22 4.6 Troubleshooting Problem Action Does not feed paper or has a paper jam.  Remove any jammed supply  Reload paper supply. Does not print 

23 4.7 Printer Supplies Part Number Description 79328I1 ANDES 3 PKG 79328I1-1 ANDES 3 PKG with Bluetooth™ 79328I1R ANDES 3 PKG 120 with MCR 7

24

25 5 Specifications 5.1 Printer Specifications Height: 2.5 inches (64mm) Width: 6.5 inches (167mm) Length: 7.5 inches (192mm) Weight: w/battery

i Contents General Precautions ... 1 Safety ...

26 5.3 Regulatory Notes 5.3.1 FCC Part 15 Class B This equipment has been tested and found to comply with the limits for a Class B digital devi

27 6 Customer Support Datamax-O'Neil Americas Orlando, FL USA Monday - Friday 8:00am - 6:00pm EST Tel: 407-523-5540 Fax: 407-523-5542 tech_suppo

ii 3.7.4 Printer Graphic Commands ... 16 3.7.5 Magnetic Card Reader Control Command

1 General Precautions  Before using this product be sure to read through this manual. After reading please keep the manual in a safe place for futu

2 1 Getting Started 1.1 Unpacking the Printer The ANDES 3 portable printer is a full featured portable receipt printer designed for varied job env

3 1.2 Installing and Charging the Battery Cartridge Note: One battery cartridge is included with the printer. Similar to a cordless phone battery,

4 1.2.2 Charging the Battery  Plug battery charger adapter output cable into the battery charger connector as shown in Figure 3. FIGURE 3 – BAT

5 1.3 Reading the LED Status The illustration below points out the location of the LED indicators described in Table 1. FIGURE 4 – LED INDICATOR